7 product ratings - John Deere M71340 Power Flow Fan Rotor 38' 46' 48' 50' 54' Rear Bagger Mower. I have a john deere gt 225 with a power flow attached. The jd dealer sold me a replacement belt for the ot model blower.The belt is too short.the serial # for the power flow is 1GX0PFCLPDD)15255. Belt is H86061 read more. John deere power flow bagger parts diagram - here you are at our website. Nowadays were excited to announce we have found an incredibly interesting niche to be reviewed, namely john deere power flow bagger parts diagram. Many individuals trying to find info about john deere power flow bagger parts diagram and certainly. 54-in bagger includes twin rear bagger hopper, chute, and Power Flow blower Tapered dual-bag design makes it easy to dump clippings Open-weave bags provide better airflow for more efficient pick-up Blower housing and fan are made of polyethylene; lightweight, will not rust or corrode.

1. John Deere Power Flow Bagger Manual Diagram
2. John Deere Power Flow Bagger Manual Lawn Mower
3. John Deere Power Flow Bagger

Installing

Installing Power Flow (54C and 62C Mowers)

MX10019

1. Install short end of long bent pin (A) in front mounting bracket (B).

MX10024

2. Install power flow (C) on long end of bent pin (A).

3. Move tension lever (D) to forward to release position.

MX10020

4. Fully raise mower deck discharge chute (E), and pivot power flow toward deck. Insert bent pin (F) into hole (G) in right rear gage bracket.

5. Rest mower deck discharge chute (E) on assembly bracket (H).

MX10021, MX10025, MX10027

Picture Note: Parts removed for clarity.

6. Power flow must install on mower deck discharge area as shown, as you insert pin (F) into hole (G).

7. Hold power flow securely against mower deck discharge area.

MX10026

8. Raise deck belt shield (I). Install drive belt (J) to top sheave (K) with belt “V” in groove.

M146337, MX10022

9. Locate belt installation label (L) on belt shield and verify correct drive belt installation. The drive belt must run:

a. from mower deck top sheave (M),

b. to idler (N),

c. to top of sheave (O),

d. to V-idler sheave (P),

e. back to mower deck top sheave (M).

10. Move tension lever rearward to the locked position.

11. Adjust mower deck and complete bagger installation.

Installing Power Flow (54D and 62D Mowers)

NOTE: Use the bent pin that comes with your Power Flow kit for the 54D mower deck. Use the bent pin from the mounting kit for the 62D mower deck.

MX37756

Picture Note: 62D Model shown.

1. Install short end of long bent pin (A) in front mounting bracket (B).

MX37757

Picture Note: 62D Model shown.

2. Install power flow (C) on long end of bent pin (A).

3. Move tension lever (D) forward to release position.

MX37758

4. Fully raise mower deck discharge chute (E), and pivot power flow toward deck. Insert straight pin (F) into hole in right rear gage bracket (G).

5. Lower discharge chute, so it rests on bracket (H).

6. Remove hardware for power flow belt shield.

M146337, MX10022

7. Locate belt installation label (I) on inside of power flow belt shield, and verify correct drive belt installation. The drive belt must run:

John Deere Power Flow Bagger Manual Diagram

a. from mower deck top sheave (J),

b. to idler (K),

c. to top of sheave (L),

d. to V-idler sheave (M),

e. back to mower deck top sheave (J).

8. Move tension lever on power flow rearward to the locked position.

9. Adjust mower deck and complete bagger installation.

Adjusting Mower Deck

John Deere Power Flow Bagger Manual Lawn Mower

1. Adjust cutting height and level mower deck side-to-side and front-to-rear as described in tractor operator’s manual.

2. Lower mower deck to pre-set cutting height.

John Deere Power Flow Bagger

3. Adjust both right-hand mower deck wheels to one position lower than they were positioned when leveling mower deck.